Riviera M370 Sports Cruiser & 12m (40 ft) Marina berth is also available

The M370 is the most popular Riviera model ever made and has been fully maintained by professionals. The layout will appeal to a family or group with ample room at the helm with a double helm seat together with a large daybed / lounge opposite. Port side hosts the wet bar and outside TV, while the starboard side has plenty of room for entertainment or dining. With the open plan layout it gives plenty of space for everyone to move through the boat with ease. Through the companion way door brings you to a comfortable fully air conditioned saloon. To port you have a large galley with solid bench tops, plenty of storage and appliances. The lounge to starboard allows the group or family to enjoy a night of board games around the table and the lounge converts to a double and single bunk when it is set up. This Riviera has two separate air conditioned double size cabins with their own doors for complete privacy. The heads (ensuite) comes with a fully enclosed shower, vanity unit and toilet. Cabins and saloon all have their own TVs.
This Riviera comes fully equipted with upgraded Raymarine 12 inch touch screen Plotter, Raymarine 9 inch Sounder and new Raymarine Autopilot, Sound system consists of a Clarion Digital Media Player, 6 CD Stacker, Combined Radio and CD Player, all new speakers, Helm Remote Control for sound system. Reconditioned Bow Thruster, New Muir Anchor Winch, Reverse Cycle Air Conditioner, 6kVA Onan Generator, 2600 watt invertor. Tender with 8 HP Yamaha outboard. Stainless BBQ. Solar panels to keep the 5 near new batteries charged. Full shade biminis and covers right over the swim platform makes fishing more comfortable, whilst the sun bed on the front deck is for those sun lovers.

This is a well looked after popular M370 sports cruiser with nothing to do but cruise away and enjoy.

WORK JUST CMPLETED
1. Work done by mechanics
a. Fully service both engines. Replace all oils. Replace all fuel and oil filters. Replace 16 spark plugs
b. Diagnostic on both engines
c. Remove exhaust elbow to check condition
d. Replace all large exhaust rubbers and hose clamps on engines
e. Starboard engine runs a slightly warmer than the port engine - checked OK
f. Bleed up fuel system.
g. Clean out throttle bodies
h. Fit new radiator caps and clear out hose to overflow bottle
i. Replace water flows flaps on both engines
j. Check steering, belts and pulleys, tension
k. Remove injector rails and clean fuel lines.
l. Put injector rails into ultrasonic cleaning system at workshop location and re-install with fuel lines.
m. Remove and replace 16 spark plugs and distributer cap and dizzy.
n. Remove and replace 4 fuel pump complete assemblies.
o. Install all new parts required, regulator kits, seals and filters on injectors.
p. Check over, run engines and recheck oils
q. On water testing ensuring both engines operational.

r. Service the ONAN generator. Filters -oil, two fuel primary and secondary. Replace spark plugs
s. Replaced water pump.
t. Clean and descale heat exchanger, (barnacle buster)
u. Check terminals and clean out airbox
v. Check exhaust elbow
w. Check water through hull, ball valve operation and clean out strainer
x. Fit and tension new fan belt
y. Check over, run generator and recheck oils

z. Remove and service both legs, including gearbox oils and anodes.
aa. Replace all bellows.
bb. Replace gimbal bearings,
cc. Replace port hydraulic rams,
dd. Replace bushes and pins
ee. Found no oil in bellows
ff. Check and replace hydraulic pressure pipelines and hoses
gg. Replace all anodes

hh. General
ii. Check leg trim - working ok.
jj. Check trim tabs - working ok
kk. Vacuum out bilge of water and wipe over
ll. Wash, drain, wipe clean bilge floor and repaint

2. Other Work at Hawkes Boatyard
a. Hawks Boatyard lift and relaunch
b. Hawks Boatyard high pressure Water Blasting of hull
c. Hawks Boatyard Hard Stand 10 days
d. Grind anti foul hull to fair off as needed, where bare back to gel coat epoxy a couple of spots
e. Clean out sea inlets
f. Clean off earth plate
g. Anti foul hull
h. Prop speed both props
i. Prop speed clear new underwater lights
j. Replace standard hull anodes.
k. Replace bow thruster anode
l. Fit two new additional anodes to the trim tabs
m. Polish Hull
n. Polish top sides
o. Remove and replace 3 high quality multifunction underwater lights